Vimalnath Enterprise

Owing to our enriched industrial experiences, we are committed to providing a wide variety of excellent quality Nitobond SBR Latex.

Usage:
For modifying and improving bonding of floor toppings, renderings and mortars; repair of worn, damaged and spalled concrete, repair of large cracks; polymer modified floor screeds; waterproof plasters for masonary and slurries.

Advantages:

• Simple to use - Single component, gauged as required.
• High - Provides excellent bond to concrete, adhesion plaster, masonry, stone work, etc.
• Improves -Gives weather resistant mortar with improved durability impermeability to chlorides and other harmful agents.
• Reduces - Provides waterproof screeds, plasters and Permeability slurries.
• Increases - Improved tensile and flexural properties strength allow thin applications.
• Versatile - Compatible with all common hydraulic cements.
• Cost effective - Nitobond SBR (Latex) is economical to use

Description :
Nitobond SBR(Latex) is modified styrene butadiene emulsion specially designed for use as a bonding aid and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external applications too.

Technical Support:

• Fosroc provides a technical advisory service supported by ateam of specialists in the field.

Chemical resistance:

• Cementitious based materials have limited chemical resitance. The addition of Nitobond SBR (Latex) to cement mortars reduces permeability and therefore helps reduce the rate of attack by aggressive chemicals.

Application instructions

Surface Preparation:

• The object of the surface preparation is to achieve a clean sound surface with a good mechanical key. All substrates should be cleaned and free of dust, plaster, oil, paint, grease, corrosion deposits, and any other deleterious substances.
• Laitence should be removed by mechanical means. Smooth substrates must be mechanically roughened e.g. by scabbling, needle gun or grit blasting to provide an adequate key.
• Corroded reinforcing steel should be exposed around its full circumference and cleaned to remove all loose scale and corrosion deposits. It is always preferably to clean the steel to a bright condition. Use of emery cloth, grit or sand blasting is recommended.

Priming:

• Reinforcing steel must be primed with Nitozinc Primer immediately after cleaning. The concrete substrate should be thoroughly dampened with water and any excess removed before being primed by thoroughly scrubbing in a slurry coat of 1 volume Nitbond SBR (Latex) to 1 volume water to 3 volumes fresh cement.
• In order to obtain a smooth consistency the cement should be blended slowly into the liquids. Stir frequently during use to offset settlement.
• Avoid ''puddling'' of the slurry coat. The topping must be applied on to the wet slurry. If the slurry dries out it must be removed and the clean substrate reprimed.

Being an eminent organization in the industry, we are involved in providing a premium quality range of Nitobond SBR.

Usage:
For modifying and improving bonding of floor toppings, renderings and mortars; repair of worn, damaged and spalled concrete, repair of large cracks; polymer modified floor screeds; waterproof plasters for masonary and slurries.

Advantages:

• Simple to use - Single component, gauged as required.
• High - Provides excellent bond to concrete, adhesion plaster, masonry, stone work, etc.
• Improves -Gives weather resistant mortar with improved durability impermeability to chlorides and other harmful agents.
• Reduces - Provides waterproof screeds, plasters and Permeability slurries.
• Increases - Improved tensile and flexural properties strength allow thin applications.
• Versatile - Compatible with all common hydraulic cements.
• Cost effective - Nitobond SBR (Latex) is economical to use

Description:

• Nitobond SBR(Latex) is modified styrene butadiene emulsion specially designed for use as a bonding aid and gauging liquid for cementitious systems. It is resistant to hydrolysis and can therefore be used for external applications too.

Technical Support

• Fosroc provides a technical advisory service supported by ateam of specialists in the field.

Chemical resistance:

• Cementitious based materials have limited chemical resitance. The addition of Nitobond SBR (Latex) to cement mortars reduces permeability and therefore helps reduce the rate of attack by aggressive chemicals.
• Application instructions

Surface Preparation:

• The object of the surface preparation is to achieve a clean sound surface with a good mechanical key. All substrates should be cleaned and free of dust, plaster, oil, paint, grease, corrosion deposits, and any other deleterious substances.
• Laitence should be removed by mechanical means. Smooth substrates must be mechanically roughened e.g. by scabbling, needle gun or grit blasting to provide an adequate key.
• Corroded reinforcing steel should be exposed around its full circumference and cleaned to remove all loose scale and corrosion deposits. It is always preferably to clean the steel to a bright condition. Use of emery cloth, grit or sand blasting is recommended.

Priming:

• Reinforcing steel must be primed with Nitozinc Primer immediately after cleaning. The concrete substrate should be thoroughly dampened with water and any excess removed before being primed by thoroughly scrubbing in a slurry coat of 1 volume Nitbond SBR (Latex) to 1 volume water to 3 volumes fresh cement.
• In order to obtain a smooth consistency the cement should be blended slowly into the liquids. Stir frequently during use to offset settlement.
• Avoid 'puddling' of the slurry coat. The topping must be applied on to the wet slurry. If the slurry dries out it must be removed and the clean substrate reprimed.

We are a reputed name in the industry, devoted towards offering the best quality array of Nitobond EP Base Resin.

Packaging size ( Base + Hardener) = 6 Litre each

Usage:
For bonding fresh wet cementitious materials to existing cementitious surfaces. For use on horizontal surfaces or on vertical surfaces where mortar or concrete can be supported by formwork. The long ‘open’ life makes it suitable for use with formwork or where additional steel reinforcement has to be fitted. The product is ideal for roads, bridges, pavements, loading bays and factories, and for bonded or granolithic floor toppings. Nitobond EP is equally suited to internal and external applications.

Advantages:

• Nitobond EP may also be used as part of a repair system where a substrate/repair barrier is required or where the substrate is likely to remain permanently damp or wet.
• Can be applied on to dry or damp substrates Exhibits high mechanical strength Positive adhesion - exceeds that of the tensile strength of the host concrete Slow cure allows time to erect steel reinforcement and formwork Solvent-free - can be used in enclosed locations.

Description:

• Nitobond EP is based on solvent-free epoxy resins contain- ing pigments and fine fillers. It is supplied as a two-com- ponent material in pre-weighed quantities ready for on-sitemixing and use. The ‘base’ component is white and the ‘hardener’ component is green, providing visual evidence that adequate mixing has been achieved. (Nitobond EPFS, suitable for cold weather working, can be made available when specifically requested.)
• Clean all surfaces and remove any dust, unsound materi- al, plaster, oil, paint, grease, corrosion deposits or algae. Roughen the surfaces, remove any laitance and expose the aggregate by light scabbling or grit-blasting.
• Oil and grease deposits should be removed by steam clean- ing, detergent scrubbing or the use of a proprietary degreaser.
• The effectiveness of decontamination and soundness of the substrate should then be assessed by a pull-off test.

Mixing:

• Any steel reinforcement and formwork should be prepared, cut to size and shape, and made ready for assembly before mixing commences.
• Care should be taken to ensure that Nitobond EP is thorough- ly mixed. The ‘hardener’ and ‘base’ components should be stirred separately before mixing to disperse any settlement. The entire contents of the ‘hardener’ tin should then be poured into the ‘base’ tin and the two materials thoroughly mixed using a suitable slow-speed drill and mixing paddle for 2 minutes until a fully uniform colour is obtained. The sides of the tin should then be scraped and mixing should continue for a further 2 minutes.

Additional Information:

• Fosroc manufactures a wide range of complementary prod-

Ucts which include:

• waterproofing membranes & waterstops joint sealants & filler boards cementitious & epoxy grouts specialised flooring materials Fosroc additionally offers a comprehensive package of products specifically designed for the repair and refurbishment of damaged concrete. Fosroc’s ‘Systematic Approach’ to

Concrete repair features the following:

• hand-placed repair mortars
• spray grade repair mortars
• fluid micro-concretes
• chemically resistant epoxy mortars
• anti-carbonation/anti-chloride protective coatings
• chemical and abrasion resistant coatings
• For further information on any of the above, please consult
• your local Fosroc office - as below.

One-part PU based Building & Expansion Joint Sealant
ADVANTAGES

• SINGLE COMPONENT WITH FAST

• RATE OF CURE

• EASY TO APPLY

• HIGH UV AND AGGRESSIVE

• ATMOSPHERIC RESISTANCE

• PRIMERLESS FOR MOST APPLICATIONS

• MOVEMENT ACCOMMODATION FACTOR-50%

• COMPLIES WITH ASTM C920-95 TYPE S, GRADE NS, CLASS 50 
• RESISTANT TO AEROBIC AND ANAEROBIC BACTERIOLOGICA ATTACK
•  DAMP SURFACE TOLERANT

Main uses

Conplast Crystalline is an integral waterproofing admixture to produce water tight concrete. The active chemical in Conplast Crystalline react with moisture available in concrete to produce non soluble crystalline formation throughout the pores of capillary tracks thus making concrete permanently sealed against water penetration from any direction.

Conplast Crystalline is developed to use in

• Water reservoir
• Tunnel concreting,
• Retaining walls and subways
• Water tank and swimming pools
• Precast unit

 

 

Advantages

• Easy to use, require only mixing with concrete.
• Integral waterproofing system.
• Crack filling property with time up to 0.4mm width.
• Exhibits good resistance to hydrostatic water pressure
  both surface.
• Compatible with our full range of water reducing
  admixture.
• Most effective due to formation of crystalline in tiny
  capillaries.
• Increase durability.